Common Errors on SP Flash Tool and some Solutions

For those who don't know, SP Flash Tool used to flash, format and read back MTK smart phones.
If you want to know more about and download this tool, click here
Here are some errors and solutions associated with SP Flash Tool hope you find them helpful.

S_FT_ENABLE_DRAM_FAIL (4032) 
This sometimes occurs when you are trying to flash a wrong ROM to your device. 
If you are sure that the firmware you are using is the exact one of your device, format the phone before you flash it.

S_NOT_ENOUGH_STORAGE_SPACE (1011)
This error pops up when size of the firmware (ROM) you are trying to flash is bigger than the space given on the phone.
Try using another version of sp flash tool. Sometimes this error occurs when using a wrong ROM.

S_UNSUPPORTED_OPERATION (1040)
The scatter file loaded is wrong. load the scatter file of your device.

S_COM_PORT_OPEN_FAIL (1003)
This error is seen when the com ports on your PC are disabled.
Try enabling com ports in your BIOS

S_COM_PORT_OPEN_FAIL (1013)
This error is just almost like the the 1003 error. Check if your com ports are available if not enable them. But most of the time using a new version of SP Flash Tool solves this problem.

S_UNSUPPORTED_VER_OF_DA (1022)
If you get this error, Use a newer version of SP Flash Tool.

S_DA_EXT_RAM_ERROR (3001)
Connection problems. Check USB cord or use another port.

S_DA_EMMC_FLASH_NOT_FOUND (3144) 
Wrong scatter file used

S_FT_DOWNLOAD_FAIL (4008)
Change USB cord or
Use Battery to flash the phone or
Change the version of SP Flash Tool. (Older versions preferable)

S_INVALID_DA_FILE (5002)
Use another version of SP Flash Tool

You can add more errors you encounter while using this tool and possibly the solution too.

89 comments:

  1. S_FTHND_FILE_IS_NOT_LOADED_YET wat of dis error tooo

    ReplyDelete
    Replies
    1. You did not specify the files for some of the partitions so the flash cannot proceed. Each partition must show where is the file to flash that partition, or you have to UNCHECK the box for that partition.

      Delete
  2. wat of BROM ERROR:S_STORAGE_NOT_MATCH (3178)

    ReplyDelete
    Replies
    1. You are trying to flash the wrong ROM onto the device

      Delete
  3. My phone is not detected... I guess the reason is bcos I mistakenly deleted my eMMC while my phone is on factory mode. What should I do now?

    ReplyDelete
    Replies
    1. Nope. If your phone is not detected by sp flash tool, its because vcom drivers are not properly installed

      Delete
  4. It not flashing and if I remove the code from the phone this is what I got brom error:s_brom_cmd_startcmd_failed (2005)
    [Brom] can not pass bootroom start command! Possibly target power up too early
    [Hint]

    ReplyDelete
    Replies
    1. Try using the latest version of SP Flash Tool

      Delete
    2. The problem is that you are turning the phone on with the power button when you are starting the flash! Do not touch the power button.

      Delete
    3. same problem please tell me solution.mobile detected but not on and not working flash tool.

      Delete
  5. Hello sir...i tried to flash my techno D9 and immediately i connect my phone it says PMT changed for this rom, it must be downloaded. please help me out

    ReplyDelete
  6. Hello sir...i tried to flash my techno D9 and immediately i connect my phone it says PMT changed for this rom, it must be downloaded. please help me out

    ReplyDelete
    Replies
    1. Select Firmware upgrade or Format + Download before u click download button.

      Delete
  7. man you are so good but d but i flashed a tecno d1, though the flashing was successful, but when i try putting the phone on, it will only boot to an extent[tecno] and then stop/hang there

    ReplyDelete
  8. when I inserted my phone, d Sp flash was showing Not Responding. what would I do?

    ReplyDelete
    Replies
    1. Is it sp flash tool showing not responding or your device is not detected by it?

      Delete
  9. I tried this process but the error reads: PMT changed for Rom; it must be dooloaded". Please help me out.

    ReplyDelete
  10. This comment has been removed by the author.

    ReplyDelete
  11. hai i tried to flash my infinix x506 j609, unfortunately the usb cable got loosen,
    now the phone is not even detecting by spflash. bt its beaing detected bt pc. please need help urgent....

    ReplyDelete
  12. BROM ERROR: TIME OUT it says what to do. and when I open my phone its only white screen. pls help me out

    ReplyDelete
  13. ERR 5069 - NO SPACE. How do I solve this?

    ReplyDelete
  14. Sir flashing stop when rich 26%
    and error 4008 we try sp tool all version my phone is Lenovo s860
    please help me

    ReplyDelete
  15. My lenovo phone is off after lenovo logo

    ReplyDelete
    Replies
    1. Look for another stock rom of your device and flash again with SP Flash Tool

      Delete
  16. brom error s_not_enough_storage_space (1011)

    ReplyDelete
  17. Brom error: s_not_enough_storage_space (1011)

    ReplyDelete
  18. My tecno P9 is been flashing by Sp flash toll v5.1352, but this msg often appear: Brom Error: S_Chip_Type_Not_Match(3168)
    Please, can somme help me know exactly about what is? Thank a lot

    ReplyDelete
    Replies
    1. Note that there are 2 types of Tecno P9 (MT6589 and MT6582)
      SO the ROM you are using is not the one for you device.
      Use the matching ROM for ur device

      Delete
  19. Replies
    1. Figu red sometimes you sd card might be what is making the phone take long to boot

      Delete
  20. AlCatel Boost View 5.0
    I think I flashed a wrong ROM, now the device is not starting at all; i tried many times to re-flash but no use.!! HELP PLEEEEEEEEASE

    ReplyDelete
    Replies
    1. You will need to download the updated version of the ROM and flash again

      Delete
  21. please help, i'm getting S_NOT_ENOUGH_STORAGE_SPACE(0x3F3) while flashing my techno y4

    ReplyDelete
  22. HELLO,WHEN I FLASH TECNO M3 KITKAT IT RECOMMAND ME TO FORMAT IT AND WHEN I FORMAT IT IT SHOWS:ERROR: s ft format fail(0xFAA)/format flash error!possibly given wrong format range,check your format setting;i need your help

    ReplyDelete
  23. Please help me I flash my techno y6 with SP flashing tools but my phone is not coming on
    Please me.

    ReplyDelete
  24. I flash my infinix X510 and download ok and d phone is not on, and I want flash again is showing me S_FT_ENABLE_DRAM_FAIL (4032) pls sir am very haste I need ur assistance

    ReplyDelete
    Replies
    1. Use the latest firmware and flash again ie android 6.0 file of X510

      Delete
  25. I tried to flash my Tecno H7, and got this error: BROM ERROR:S_DL_READ_FAIL(5073). Please what do I do?

    ReplyDelete
  26. My phone refuse to startup after flashing, it still booting for about 50 mins now

    ReplyDelete
    Replies
    1. What phone is that? You can do a factory reset from recovery to support the rom reload, this should fix your problem or retry the flashing process but with format all + download this time around

      Delete
  27. infinix hot4 x557 .flash tool updated check.change cable.drivers install.but still not flashing.

    ReplyDelete
  28. white screen after flashing what to do ?

    ReplyDelete
  29. erro: status sec imgdhr type mitmatch

    ReplyDelete
  30. 'error:qthelp://com.mediatek.flashtool/doc/S_INVALID_BBCHIP_TYPE.htm
    What should I do

    ReplyDelete
    Replies
    1. hello, i got the same problem here...any fixed afterward?

      Delete
  31. hello sir, I have Tecno H6, I format my frimware and put new one using Sp flash tools, and it copleatly 100%. But now my phone only stuck on tecno logo and restart again. please help

    ReplyDelete
  32. i reflashing my bv ultra using this rom and my screen turn white and rainbow color.. any one can help me to fix it ? thanks.

    ReplyDelete
  33. Hello ... Please help me to wake up my Infinity Hot 4 lite, I tried to do an update when trying to install the Naugat 7.0 on my Infinix Hot 4 Lite  and my phone not responds again. It seems that I have deleted everything in the the phone's memory because its was with the bad Rom, even the Preload and the boot Loader are deleted. Please help me to resolve this problem that affects me seriously....

    Thanks in advance.

    ReplyDelete
  34. Plz help ...... I tried to flash my dead infinix hot 3 but it is giving me this error:
    "Storage type mismatch!
    scatter storage type is hw_storage_emmc
    target storage type is hw_storage_none"

    ReplyDelete
  35. I flashed x601 note3 it but not work well I used another rom, it refuse to power on. I try to use the one I used before is connecting.

    ReplyDelete
  36. Pls I need w3 real flash file I flash one become dead pls

    ReplyDelete
  37. Thanks for another wonderful post. Where else could anybody get that type of info in such an ideal way of writing?
    smartphone flash tool

    ReplyDelete
  38. Pls i try flash my p5 is showing
    DA file is not loaded corect
    ROM path dose not exist

    ReplyDelete
  39. I have 2 problem 1. S_FT_GET_MEMORY_

    2.my tecno p5 it given message on screen, Encryption Unsuccessful how remove it. Thakns

    ReplyDelete
  40. i just flashed my tecno W2 and it is starting up with a coloured stripped screen, i used SP flash tool please what can i do because the flashing completed succefully
    ??

    ReplyDelete
  41. i just flashed my tecno W2 and it is starting up with a coloured stripped screen, i used SP flash tool please what can i do because the flashing completed succefully
    ??

    ReplyDelete
  42. I flashed my techno w3 with a wrong pre-loaded. Now it cannot switch on or charge. How can I unbrick it?

    ReplyDelete
  43. This comment has been removed by the author.

    ReplyDelete
  44. ROM[logo] checksum mismatch checksum config checksum val, plz help when i open to the scatter load it bring this msg how can i fix ?

    ReplyDelete
    Replies
    1. Delete checksum.ini file inside the firmware folder

      Delete
  45. I can't download Lenovo a678t firmware from this site, some odds used to blocked me, help pls.

    ReplyDelete
  46. I have atecno n2s and wrongly ifalshed it using tecno n2 firmware any assistance please iwllI appreciate the phone cantc be flashed again

    ReplyDelete
  47. tecno c5,black display after flashed

    ReplyDelete
  48. BROM ERROR S_TIMEOUT 1042 HOW TO FIX IT?

    ReplyDelete
  49. it flashed successful to my infinix 557 but no cellular connection. please help cousin

    ReplyDelete
  50. S_INVALID_BBCHIP_TYPE(1003) This error was display when i tried to flash zte
    pls help

    ReplyDelete
  51. help with Tecno la6 file password.

    ReplyDelete
  52. I Root my tecno CX air with sp flash after that I went and uninstall some of the systems software unfortunately my phone went off and came on but stuck boot mode with tecno logo on the screen. I went to twrp recovery mode I clear the cache and factory rest the phone but still not stuck on boot. The phone is not charging I went to Sp flash tools I flash the recovery images with download mode and when it completed the phone was not still stuck on Boot mode. I went and format the phone with the Sp flash tools after format completed I removed the cable from the phone and close the Sp flash tools I try to put the phone on but it was not come on again.I went I plug it to the computer I here the beep sound.
    I open Sp flash tools and choose download but this was the message I got showing me S_FT_ENABLE_DRAM_FAIL (4032). I went and download the firmware for the phone trying to format but the same message showing me the same message S_FT_ENABLE_DRAM_FAIL (4032)
    Sir my phone is not coming on I went I download Sp flash tools 3.0 the latest I open the Sp flash tools but when I went to the scatter files it do not want to load to the Sp flash tools.
    But when I try the old Sp flash tools it load all the files but the same message coming on the old Sp flash tools showing me S_FT_ENABLE_DRAM_FAIL (4032).
    But the new Sp flash tools is not loading the scatter files. Sir please help me my phone is not coming on. MY phone is Tecno CX air Chip set is Mt6737.

    ReplyDelete
  53. Zebedee Davis I Root my tecno CX air with sp flash after that I went and uninstall some of the systems software unfortunately my phone went off and came on but stuck boot mode with tecno logo on the screen. I went to twrp recovery mode I clear the cache and factory rest the phone but still not stuck on boot. The phone is not charging I went to Sp flash tools I flash the recovery images with download mode and when it completed the phone was not still stuck on Boot mode. I went and format the phone with the Sp flash tools after format completed I removed the cable from the phone and close the Sp flash tools I try to put the phone on but it was not come on again.I went I plug it to the computer I here the beep sound.
    I open Sp flash tools and choose download but this was the message I got showing me S_FT_ENABLE_DRAM_FAIL (4032). I went and download the firmware for the phone trying to format but the same message showing me the same message S_FT_ENABLE_DRAM_FAIL (4032)
    Sir my phone is not coming on I went I download Sp flash tools 3.0 the latest I open the Sp flash tools but when I went to the scatter files it do not want to load to the Sp flash tools.
    But when I try the old Sp flash tools it load all the files but the same message coming on the old Sp flash tools showing me S_FT_ENABLE_DRAM_FAIL (4032).
    But the new Sp flash tools is not loading the scatter files sir please help me my phone is not coming on. MY phone is Tecno CX air Chip set is Mt6737.

    ReplyDelete
  54. ERROR: S_BROM_DOWNLOAD_DA_FAIL(2004)

    ReplyDelete
  55. The lead scatter file is invalid.. For infinix x5515

    ReplyDelete
  56. Please my Tecno cx Air went dead after flash Please what do i do? System still detects

    ReplyDelete
  57. Please help, i have tecno droid p701, all of a sudden all apps keeps force closing, have clear app preferences, restart but still not working...
    I did factory reset but everything remain intact, nothing removed...
    I boot into recovery mode and did wipe data, still nothing removed, i downloaded the exact rom and flashed it which got flashed successfully with green mark..

    When I boot up the device, everything was still on it as it was before i flashed...

    Factory reset, data wipe in recovery and flashing doesn't do anything to the device...

    All files, wallpaper, settings etc doesn't get reseted no matter what i do...

    Need help pls...

    ReplyDelete
  58. Tecno cf7 common 11 flash with so tool but error authentication why ?

    ReplyDelete
  59. This comment has been removed by the author.

    ReplyDelete
  60. Tecno cf7 common 11 flash with sp tool but error authentication why ?

    ReplyDelete

    ReplyDelete
  61. I think that each of you is faced with the need to quickly convert PDF format. I advise you to bookmark this useful resource https://www.pdfplatform.com/ where you will find all the tools for successful and fast file conversion. You can also quickly organize pages in PDF files and split files into several. This is very convenient when all PDF tools are collected on one site.

    ReplyDelete
  62. Help sir I try to flash my infinix zero 5 x603 I get error say INVALIP GPT

    ReplyDelete

Related Posts

Related Posts Plugin for WordPress, Blogger...