How to unbrick dead Infinix Note 2 X600 after flashing wrong ROM/Firmware (Test Point)

Lots of people do get confused when trying to flash or upgrade infinix note 2 X600 because of the many variants of ROMs/firmware they are faced with so most times they end up flashing the wrong one. Once this happens, if you are lucky the device will still be able to be detected by PC which in that case you will be able to flash another ROM.

If you noticed that PC can no longer detect the Infinix Note 2 X600 you are trying to flash or upgrade, you will need to use the test point method to make PC able to detect the device again.

On a normal, the test points of most MTK devices is usually joining the two gold points with label KCOLO (KOLO, COLO) & GND you can read more of this from here. There is no KCOLO gold point on  Infinix Hot 2 X600 board so the method from the link above will not work on this device.

Now to get the infinix X600 detected, you will have to do the following below.

Note
Do this at your own risk!

All you need here is just a little hardware knowledge ie how to solder a connecting wire on the board.

First of all you will have to know the right ROM/firmware of the device you want to flash. 
X600-H533-A1
X600-H533-B1
X600-H532-A1
If you are still confused, check on the board as shown on the picture below to determine the one you are supposed to flash. You can now download the ROM from here



After you have downloaded the ROM, use either SP Flash Tool (latest version), Infinix Flash Tool, Wiselink Tool to load the scatter file then click Download Button.
If you are using SP Flash Tool, Select Firmware upgrade.

Now solder the connecting wire on the board as show on the picture below (red square). Also make sure the socket as shown in the image is clipped to the board (It leads to the usb port).
Also make sure battery socket is not connected to board.


After you have soldered the wire and clipped the usb socket on phone board, connect the phone to PC with USB cord.
Now take the other end of the connecting wire and touch and GND (Ground) on the board. When the phone is detected by PC, release the wire from GND point and wait for flashing process to complete










25 comments:

  1. Wow..lovely..can u help with the same process for hot 2

    ReplyDelete
  2. Please Tking, how do I solve error 4032 of sp flashing. No matter d correct file I used, it always give this error flashing. Thanks sir

    ReplyDelete
    Replies
    1. Which device are u flashing

      Delete
    2. Imfini x600 show erro when flashing the rom useding sp flash tools

      Delete
  3. infinix x600 show error when flashing the rom use sp flash tool same problèm with bro andre pls help how set

    ReplyDelete
  4. pls my rom firmware is h532 B1 what should i do

    ReplyDelete
  5. mine is 533 c1 is there any rom like that

    ReplyDelete
  6. Bro phone is'nt detected even with jumper trick . Please tell me if there is another way.

    ReplyDelete
  7. tanks sir you save my fone,if anyone get missmatch because after conect pc ground stiil conect on bord ..remove quickly is tested 1000%

    ReplyDelete
  8. hi pls help me with my x600 after the connection of force boot i flashed it but it did not work out it comlain brom error

    ReplyDelete
    Replies
    1. Do not solder the wire on board.

      When u connect the phone to pc with usb, touch the test point with the jumper wire and then when it shows its connected on flashtool (red line) disconnect the jumper wire.
      I like doing stuffs like this using tweezzers (aka picker) instead of jumper wires.

      Also make sure u are using the right firmware of the device.

      Delete
    2. nice just do for my infinix x600 h532 a1 work full

      Delete
  9. My x600 shows battery if plug to a charger, but does not power on. I have flashed it using infinix flash tool but it still doesn't power on. Pls what do I do

    ReplyDelete
  10. May almighty God bless you. Thanks so much

    ReplyDelete
  11. This comment has been removed by the author.

    ReplyDelete
  12. pls where can i get x600 h532 b1 firm ware

    ReplyDelete
  13. Thanks so much it work perfectly

    ReplyDelete
  14. Please when I flash the phone Infinix x600 to unbrick it,
    It can't And it shows..BROM ERROR: S_STORAGE_NOT_MATCH (OxC6F)

    ReplyDelete

Related Posts

Related Posts Plugin for WordPress, Blogger...